what is the function of pull push rule in assembling a wooden scaffold
1. what is the function of pull push rule in assembling a wooden scaffold
Answer:
the function to pull rull is push ap
2. 1. what are the functions of try square.2. what are the functions of pull push rule.3. what are the functions of dividers.
Answer:
Try Square – used for checking flatness and squareness. This is a tool used for measuring and testing the squareness of corners
Pull-push rule – used for measuring long, short, straight lengths.
Divider – used for dividing distances. This is used to draw a small circle or divide a straight line into equal dimension and length.
3. what is the function of the given items. 1.Test light2.Voltmeter3.Pull-Push Rule4.Clamp Ammeter5.Wire Gauge
Answer:
A test light, test lamp, voltage tester, or mains tester is a piece of electronic test equipment used to determine the presence of electricity in a piece of equipment under test.A voltmeter is an instrument that measures the difference in electrical potential between two points in an electric circuit. An analog voltmeter moves a pointer across a scale in proportion to the circuit's voltage; a digital voltmeter provides a numerical display.A push pull rule is a measuring tape that coils into a compact case. It is used for measuring long, short, straight lengths.A clamp-on ammeter is a meter that measures the current in a circuit by measuring the strength of the magnetic field around a single conductor. Clamp-on ammeters measure currents from 0.01 A or less to 1000 A or more.Wire gauge is a measurement of wire diameter. This determines the amount of electric current the wire can safely carry, as well as its electrical resistance and weight.Explanation:
HOPE IT HELPS
#CARRYONLEARNING
4. Learning Task 2: Categorize the following tools and equipment into the following according to their function. Write the letter corresponding thecategoryA. MEASURINGB. MARKING/LINING C. TESTING D. EDGE-CUTTINGE. TOOTH-CUTTINGF. BORINGG, HOLDINGH. PORTABLE POWER TOOLSJ. DRIVINGK.PERSONAL PROTECTIVE EQUIPMENT (PPE) L. MISCELLANEOUS1. Push-pull rule2. Chalk line3. Level Bar4. Plane5. Crosscut saw6. Drill bit7. Bar Clamp8. Jigsaw9. Nail set10 PaintbrushPaki answer Plsss...
Answer:
1 A
2 B
3 C
4 J
5 H
6 L
7 G
8 D
9 E
10 F
Explanation:
yan Lang alam Ko po sorry kung mali rin po
5. DIRECTION: State the use or function of the given electrical measuring toolsand instruments.ELECTRICAL MEASURING TOOLSUSE OR FUNCTIONAND INSTRUMENTS1.TEST LIGHT2. VOLTMETER3.PULL- PUSH RULE4. CLAMP AMMETER5. WIRE GAUGE
Answer:
1. A test light, test lamp, voltage tester, or mains tester is a piece of electronic test equipment used to determine the presence of electricity in a piece of equipment under test. ... Properly designed test lights include features to protect the user from accidental electric shock.
2. A voltmeter is an instrument used for measuring electrical potential difference between two points in an electric circuit. An ammeter is a measuring device used to measure the electric current in a circuit.
3. A push pull rule is a measuring tape that coils into a compact case. It is used for measuring long, short, straight lengths.
4. A clamp meter is an electrical test tool that combines a basic digital multimeter with a current sensor. ... Beneath their plastic moldings, hard jaws consist of ferrite iron and are engineered to detect, concentrate and measure the magnetic field being generated by current as it flows through a conductor.
5. Wire gauge is a measurement of wire diameter. This determines the amount of electric current the wire can safely carry, as well as its electrical resistance and weight.
Explanation:
I HOPE ITS HELP PAKI FOLLOW AT BRAINLIEST PO SALAMAT, GBU6. 20. When making a request you shouldA. Fill up the duly requisition formB. Submit to the teacher for checkingC. List down the materials and tools neededD. All of the above21.M-3) It is the length, depth, and thickness of an object.A. Inside caliper B. micrometer C. outside caliper D. pull push rule22. It is the measure around the circle.A. circumferenceB. diameterC. length D. pressure23. Which of the plumbing measuring tools that can measure the outsidediameter of pipe.A. inside caliperC. pull push ruleB. outside caliperD. none of the above24. It is expressed as series of the digits 0 and 1 that appears on the screen ofan instrument.A. diameter B. digital C. length D. tape measure25. This is the device or implement used especially held in one the hand tocarry out a particular function.A. equipment B. pressure gaugeC. tool D. materialsTLE
Answer:
d
a
b
c
Explanation:
sana maka tolong
7. a. 2x2 lumber b. stock c. materials d. substrate 14. Student X is classifying carpentry tools according to their uses and while doing the task there are four tools that are placed in one side. Which of the following tool is not belong to the group? a. saw b. plumb bob c. try square d. level bar 15. Edna needs to check the squareness and flatness in laying hallow blocks, what tool does he need to accomplish the task? a. protractor b. pull-push rule c. try square d. compass 16. Which of the following is one of the most accurate tools for guiding and testing work in establishing a horizontal level? a. hose level b. Plumb level and spirit level C. plumb bob d. Level bar 17. In the fixing of form panels assembly James and John are worried in levelling the height of every post. What is the right tool should they used to check the horizontal alignment of every post? a.hose level b. Plumb level and spirit level c. plumb bob d. All of these 18. Which of the following tool is used both for guiding and testing the work up to a vertical or horizontal position. a.hose level b. Plumb level and spirit level c. plumb bob d. All of these 19. Which of the following is not a leveling instrument? a. hose level b. Level bar c. plumb bob d. Marking gauge _20. Which of these tools has string and weight at the end? a. hose level b. Level bar c. plumb bob d. Marking gauge _21. Mark is conducting an inventory of tools in the laboratory and he found out that there are 5 tools that are not working. What is the label the 5 tools? a. functional b. serviceableSc. condemnable d. non-functional _22. James is classifying the tools in the tool cabinet and he is confused where should he place the claw hammer, if you were James where will you put the claw hammer? a. boring tools b. driving tools c. tooth-cutting tools d. measuring tools _23. Eljohn is asked to measure a long lumber. What measuring tool will he use? a. meter stick b.ruler c. pull-push-rule d. try square _24. The grade 7 kuliteng and solibao are assembling a long table then suddenly their teacher got angry because one of them wipe the pull-push rule with his bare hands. What is the proper way of cleaning the blade of pull-push-rule? a. wash with water and gasoline b. wipe with paper or plastic C. wipe with rag or cloth d. just use it without cleaning 25. John is looking for a zig zag rule but he found out that it's not functional and it needs a little oil on the joints. What is the label of the tool? a. functional b. unserviceable C. condemnable d. non-functional but serviceable _26. The grade 7 students are demonstrating the proper way of handling measuring tools during their TLE class. Which of the following shows the proper way of handling tools? a. use caliper as tongs b. wipe off the blades of measuring tools using your bare hands c. oil the movable parts of pull push rule d. no answer 27. Jessa is task to check the condition of tools. Which of the following is the first step in segregating and labelling tools? a. record the number of functional and non-functional tools b. segregate serviceable and unserviceable tools C. conduct an inventory of tools d. label tools and equipment 28. It is the condition where high standard of good housekeeping is maintained so that there is no dust and rust anywhere. a. sort b. sweep C. systematize d. sanitize 29.It ensures the safety of the construction workers. a. signs, signal & barricades b. exit signs c. danger signs d. safety instructions signs 30. Which of the following is the proper way of handling tools? a. make calliper as tongs b. clean the steel tape/blade with bare hands C. clean the blade/steel tape with cloth or rags d. no answer
Answer:
A
C
B
B
A
C
A
C
C
A
B
B
C
A
C
B
B
A
C
A
A
C
B
A
B
B
C
A
C
C
8. true or false1. Analog mul tester are those that have a needle that stops on the numberthat is printed behind the moving needle.2. Analog multi tester is the most commonly used by the technician becausethe movement of the pointer or deflector shows defective components.3. Right zero adjustment screw is used to adjust pointer or deflector inright Infinity of the voltohmmeter (VOM).4. Range selector allows changing the function and scale of the mult!tester5.Applied voltage in parallel connection is the sum or total of individualvoltage drops.6. Total resistance in parallel is almost equal or less than the lowestbranch resistance value7. Load/oads are connected in parallel when it connected one after theother8. Ohmmeter used to measure electrical pressure or voltage of a circuit9. The unit of measurement of current electricity is expresa in ampere,10. The unit of meesuromont of current electricity is express in ampere11. Voltmeter is a device used to measure EMF in the circuit.12. Foot rule is a measuring tool used to measure the length of an objectcentimeter and inches13.Micrometer is used to measure the diameter of wires/conductors incircular mills.14. Pull push rule is a device used in measuring small and big sizes ofwires and cables.15. Test light or buib tester is a pocket size tool used to test the line wireor circult of the current on it.pa sagot naman po. Asap
Answer:
1. t
2. t
3. t
4. f
5. t.
6. f
7. t
8. t
9. t
10. t
11. f
12. f
13. t
14. t
15. t
Explanation:
ty for points pa brainliest
9. Directions Give the functions/uses of the following carpentry tools,1. Claw hammer2. Plumb bob3. Push pull rule4. Zigzag rule5. Level hose6. Bench vise7. Hack saw8. Tri- square9. Electric drill10. Spirit level
Answer:
1. Claw Hammer - A claw hammer is a tool primarily used for driving nails into, or pulling nails from, some other object.
2. Plumb bob - A plumb bob, or plummet, is a weight, usually with a pointed tip on the bottom, suspended from a string and used as a vertical reference line, or plumb-line.
3. Push Pull Rule - A push pull rule is a measuring tape that coils into a compact case. It is used for measuring long, short, straight lengths.
4. Zigzag Rule - A rule composed of light strips of wood joined by rivets so as to be foldable, all the opening and closing parts being in parallel planes.
5. Level Hose - The water level is often used to determine the level spot on 2 items that are at a distance from each other, such as posts or stakes in the ground.
6. Bench vise - What is a bench vise? To state in simple terms, a bench vise is a mechanical apparatus used to secure an object that is to be worked on.
7. Hack Saw - A hacksaw is a fine-toothed saw, originally and mainly made for cutting metal.
8. Tri - Square - A try square or try-square is a woodworking tool used for marking and checking 90° angles on pieces of wood.
9. Electric drill - A drill or drilling machine is a tool primarily used for making round holes or driving fasteners.
10. Spirit level - A spirit level, bubble level, or simply a level, is an instrument designed to indicate whether a surface is horizontal or vertical.
10. TLE1. TRUE OR FALSE Directions: Read each statement carefully. Write the word TRUE if the statement is correct and FALSE if not. Write your answer on the space provided before each number. 1. Consider the different sizes, types, and shapes so as the measuring instrument 2. Temperature, humidity and pressure of an object to be measured 3. Wipe measuring tools that are made up of thin steel sheets using bare hands. 4. Pull too much retractable measuring tool like pull-push rule to prevent difficulty in putting it back to its case. 5. User of the tool must be identified beforehand to consider his or her knowledge and skill in using measuring tools 6. Choose measuring tool that is affordable but will not sacrifice the quality and accuracy of measurements. 7. Check the functionality of measuring tools and its parts once in a year 8. Do not avoid rough particles around measuring tools because they can erase graduations on the measuring tool through friction 9. Regularly clean and wipe not only the measuring tools but also its storage. 10 Soak measuring tools in water that have movable parts to prevent it from stocking up
Answer:
1.True
2.True
3.True
4.True
5.True
6.True
7.True
8.True
9.True
10.True
11. pahelp hehx4. Which of the following does not belong to the group of the Hand tools?c. Hand toolsd. Power toolsa. Wrenchesb. Air chisel5. These are Machine/Power tools, except:c. Pliersd. Screwdriversa. Pullersb. Vacuum cleaner6. This wrench uses compressed air to quickly and powerfully turn nuts, bolts, and other objects.c. Grinding tool d. Electric drilla. Air drillb. Air racket c. Pneumatic Torque Wrench d. Pneumatic floor jack7. It is otherwise called as Multi-tester is used to measure the voltage, resistance and current of acircuit.a. Voltmeter b. Clamp Ammeterc. Ammeter d. Volt-Ohmmeter (VOM)8. It is used to measure current flowing in a conductor and is also called as Tong-tester.a. Clamp Ammeter b. Pull-Push rulec. Wire Gauge d. Test Light9. It is used to measure the diameter of wire/conductors in circular mils.a. Ruler/foot ruleb. Micrometerc. Test Lightd. Pull-Push rule10. It is a pocket size tool used to test the line wire or circuit if there is current in it.a. Test Lightb. Ruler/foot rule C. Ammeter d. Clamp Ammeter11. It refers to the vibration or extra noise from the operation means problems on parts and accessoriesstarted to develop.a. Functionalityb. Power supply c. Persons involved d. Performance12. It refers to the technical person who has the knowledge and skills about the technology.a. Visual inspectionb. Functionalityc. Persons involved d. Performance13. These are method of identifying non-functional tools and equipment, except:a. Visual inspectionb. Performancec. Power supply d. Functional Inventory14. Which of the following does not belong to the group of the classifications of tools and equipment:a. Hand toolsb. Holding toolsc. Driving tools d. Measuring tools15. It is used for electrically operated only.a. Electrical equipment b. Power supplyc. Power tools d. Machine tools
Answer:
4.d
5.c
6.a
7.b
8.a
9.b
10.c
11.c
12.d
13.b
14.d
15.d
Explanation:
check me if im wrong
#CARRYONLEARNING12. B. Direction: Each item below is composed of 4 choices with pair of words or phrases. Analyze each pair and choose which pair indicates correct function of the electrical measuring tool or instrument. 1. a. Test Light : Wire diameter c. Ruler : Wire Size b. Ohmmeter : Current d. Pull-push Rule : Length of an object 2. a. Micrometer : Voltage b. Wire Gauge : Size of wire c. Ammeter: Voltage d. Voltmeter : Current 3. a. Clamp ammeter : Voltage c. Test Light : Wire length b. Volt Ohmmeter: Resistance, Current, Voltage d. Ohmmeter : Voltage 4. a. Voltmeter : Voltage c. Wire gauge : Length, width and thickness of object b. Ammeter : Resistance d. Ruler : Wire diameter
Answer:
1 b.
2. a.
3. a.
4. b
5.a
Explanation:
I hope it helps you have a good day
13. 1. Yohance wants to fasten and remove nails. Which tool is appropriate? a. screw driver b. file c. Hammer d. pliers 2. Rafaelle wants to cut lumber across the grain. Which tool is appropriate? a. coping saw b. crosscut saw c. hacksaw d. backsaw 3. What tool is used to smoothen the surface of wood? a. hammer b. saw c. hand drill d. wooden plane 4. If screw is for Screw driver, what about nails? a. nut b. mallet c. hammer d. chisel 5. Thirdy wants to measure long distances, Which tool is appropriate? a. pull push rule b. ruler c. meter stick d. tri-square 6. Why do we need to take care of the industrial arts tools? a. It will save you time and money b. in order to preserve their function for years to come. c. all the answers are correct d. So that it will not get rusty 7. Which of the following is not an example of Graphic works? a. Bill board b. sign board c. tv screen 8. Which should be the first step in project making? a. cutting b. assembling c. finishing d. measuring 9. Which of the following materials is used for finishing a project? a. screw b. glue c. paint d. nail
Answer:
im a teacher po eto po answer
Explanation:
1.a
2.d
3.c
4.c
5.d
6.a
7.a
8.d
9.d
14. 1. TRUE OR FALSE Directions: Read each statement carefully. Write the word TRUE if the statement is correct and FALSE if not. Write your answer on the space provided before each number.1. Consider the different sizes, types, and shapes so as the measuring instrument 2. Temperature, humidity and pressure of an object to be measured. 3. Wipe measuring tools that are made up of thin steel sheets using bare hands, 4. Pull too much retractable measuring tool like pull-push rule to prevent difficulty in putting it back to its case. 5. User of the tool must be identified beforehand to consider his on her knowledge and skill in using measuring tools. 6. Choose measuring tool that is affordable but will not sacrifice the quality and accuracy of measurements. 7. Check the functionality of measuring tools and its parts once in a year.
Answer:1.true2.true3.false4.true.true
Explanation:i dont really know if my answer in 3 is correct
Answer:
1. False
2.False
3.True
4.True
5.True
Explanation:
corect me if i am wrong po thankyou i hope its help # cary on learning☺
15. doc Score IMultiple Choic hoice: Choose the correct ar ber dnswer, Write your answer in the spce provided before each iu 1. Which of the following is used for measuring lonE a. pull-push rule 2. Which of the following is a p used for measuring long distances? b. ruler C. tape measure d. meter stick a powdered substance which when mixed with water 3. Which of the following is used to hold the workpiece during operations such as sawIng. pran aggregates? acts as binder of A. sand b. lumber C. soil d. cement and drilling? a. claw hammer ng operations such as sawing. planning b. plumb bob d. C-clamp which of the following is used to hold a wood or metal work piece and is used in carpentiy and c.bench vise welding a. claw hammer b. plumb bob C. bench vise 5. Which of the following is the first step in receiving delivered iterms/goods? d. C-clamp a. Find purchase order b. Verify that the delivery corresponds to an open P.O C. Determine whether correct materials was received d. Review and correct receiving transactions as necessary 6. The following are parts of a Bill of materials except a. Quantity tells the amount of materials to be purchased b. Units gives the measure of materials to be purchase C. Yield gives the number of portions of each dish d. Amount is the cost of all materials -7. What is the second step in segregating and labeling non-functional tools and equipment? a. Conduct an inventory of tools and equipment b. Record the number of the non-functional tools and equipment C. Segregate tools that are serviceable or unserviceable d. Report the number of tools and equipment that are non-functional but subject for repair 8. Which of the following is used in setting the head of a finishing nail below the surface of the wood C. Screw driver d. goggles b. mallet 9. Which of the following is used to prevent the inhalation of sprayed paint fumes? C. apron a. nail set d. gloves b. face mask a. goggles 10. Which of the following tooth-cutting tool is used to cut the wood along the grain? d. compass saw C. back saw b. rip saw a. cross-Cut saw
Answer:
12345678901234567890
16. Self-Check 1.2 d. job MULTIPLE CHOICES: Choose the letter of the correct answer that corresponds to the statement/question. Write the letter of your answer before the number. 1. Which of the following tools/materials is made out of metal used for fastening? a. nail b. saw c. lumber Vd. screw driver 2. What do you call the tool that is used for measuring long distances? a. hammer b. level bar c. meter stickad. pull-push rule 3. Which of the following is used for driving and pulling nails? a. claw hammer b. level bar c. meter stick i bed. pull-push rule 4. What do you call the tool that is used in checking vertical and horizontal position? a. nail b. saw C. spirit level d. screw driver 5. Which of the following is a piece of work of a definite extent or character for a set of fee. a. material b. tool c. bill 6. The grade 7 students are task to list down the tools that are functional, non-functional, serviceable and condemnable. What do you call these process? a. lubricants b. inventory C. Scaler d. stock 7. Which of the following refers to the indicated name of tools and equipment? a. lubricants b. label c. scaler d. standard 8.John is a carpenter and he needs carpentry tools that is operated by electricity to make his work faster and easier. What do you call these tools? a. hard ware b. hard tools C. power ware d. power tools 9. Which of the following known as metal supplies used in furniture? a. steel b. hardware c. lubricants d. steel bar 10.John Dave is task to repair all the tools in the cabinet tool and he observe that the joints of some tools like compass, pull-push-rule, and others are rusting and stack. What does John Dave needs? a. advance b. standards c. lubricants d. lubricator 11. After the first period in the morning Erick is task to classify carpentry materials according to their uses. What do you call these process? a. store b. stock C. segregate d. substrate 12. The furniture shop of Mr. Lee has a lot of lumber stored in one area. What is the term used for these lumbers stored? a. stack b. stock C. segregate d. substrate 13. What do you call the wood to be cut in a cutting machine?
Answer:
1 a.2. B 3. D4. A5. A6. D7. C8. B9. D.10. D.11. C.12. A.13. A.Explanation:
hope it helps po ☺️17. AssessmentDirections: Identify what is being referred to in each item and choose the best answerfound inside the box.Disc cutterHydraulic CraneMaintenanceElectric DrillHydraulic PressPneumatic ToolElectric GrinderHydraulic toolPush pull ruleElectric ToolTroubleshooting1. Measuring tool used to measure longer distances available from oneMeter to 50 meters long.2. An electric tool is used to bore holes to walls and materials,3. A power tool is used to shape and shave off materials.4. A hydraulic tool used to mold or bend materials with extreme force.5. An activity of preserving or prolonging a tool's serviceable life.6. A type of tool that uses electricity to function,7. A power tool used to lift object by the use of hydraulic arms,8. A type of power tool that uses compressed air to function.9. An electric tool used to cut materials such as metal and wood,10. A type of tool that use liquid pressure to function.
Hello there @Clarksonfrancisco799
These are the answers for your questions:
1. Push pull rule
2. Electric drill
3. Disc Cutter
4. Hydraulic Press
5. Maintenance
6. Electric Tool
7. Hydraulic Crane
8. Pneumatic Tool
9. Electric Grinder
10. Hydraulic Tool
Hope you get a perfect score on this
18. Choose the correct letter. Write your answer on the space provided before each number.A.B.1. What is the most common material used in carpentry?a. nailsA.b. wood2. Which word best describes or refers to a lumber for a certain carpentry job?c. paintd. sandAlc.a. stockb. standardC. Scaled. segregate3. Why do we need to identify tools and materials in carpentry?a. Avoid delaying of workc. easy to prepare for the right jobb. easily pick-up from the tool boxd. all of the above4. Why do you think the pull push rule is used to measure long distances?a. because it can measure up to 10 metersc. because it is easy to useb. because it is light and handy toolDd. because it is a flexible rule5. Why do we need to check the conditions of tools and equipment?a. maintain the sharpness and functional tools and equipmentb. test the functionality of the tools and equipmentc. identify the tools and equipment need repair/replaced. all of the above6. Can you identify which is an object used as parts or components of the projects?a. equipment b. materialsc. toold. hardware7. What is the main idea when we say it is a measurable extent such as length, thickness and width?a. dimensionb. fractionc. graduationd. mensuration8. Why do you think meric is an international system of measurement?a. easy to readc. it is broken down into smaller measurementb. a decimal systemd. all of the above9. What would be the result if the number is expressed in a counting system that uses units of 10?a. it becomes a fractionc. it becomes a decimalb. it becomes a standard numberd. it becomes a whole number10. Using on what you have learned on conversion of units, how will you convert centimeters into millimeters?a. multiply the number by 1?c. multiply the number by 10?b. multiply the number by 100?d. multiply the number by 1000?11. How would you calculate a boardfoot in lumber using on what you have learned?multiply the thickness, length and width and divide it by 12b. divide the thickness, length and width and multiply it by 12add the thickness, length and width and subtract it by 12d. subtract the thickness, length and width and add it by 1212. In the ways of taking measurement, can you distinguish which one is the first?a. Layout the widthc. measure edge to edge with a measuring toolb. measure end to end of stock using a measuring too! d. measure inside diameter with a caliper13. Why do you think measurements must be obtained according to job requirements?a. so that no materials will be wastedc. time will be more consumedb. quality product is attainabled.both a and c14. What are some of the factors that cause some of the measuring tools to be damage?a. They were wiped before returning to the storage roomb. Movable parts are oiled to avoid stock-upPull push rules are pulled too muchd. Checking the graduations of the tools after use15. Why do you think measurement is important in our day-to-day life?a. Because it teaches us how to measure.b. Because it provides a standard for everyday things and processes.Because it gives correct data and results.
Answer:
1.B
2.B
3.D
4.?
5.D
6.A?
7.?
19. 1.what do you think is the function of the encircle part of the try square? A.Nothing,just handle B.Both have graduations C.Only design D.For market value 2.How is the pull-push rule similar to a ruler as a measuring instrument? A.Both can measure long distance B.Both have graduations C.Both have spring coil D.Both can be a least 3 meters in length. 3.As beginner,which is more effective and easier in,reading inch measurements? A.Count each of the graduations by one B.Count the graduations by four C.Count the graduations by two's D.Count the graduations by eight Help me po sa assignment ko
Answer:
1.b 2.a 3.d
Explanation:
pls pa brainliest po
20. Direction: Below are the list of jumbled electrical tools. Classify or Group them according to their used and functions.Test lightHand drill and bitsClamp-Ammeter Hook meterRulerPush-Pull RuleMuliti-Tester/Multi-meterNut DriverGimletCombination plierStar drillDiagonal plierAuger braceHammerWire stripperElectician knifePhilip ScrewdriverWire gaugeLong nose plierPortable Hand drillOutside micrometer caliperFlat screw
Answer:
hindi ko magits ang ramo po kasi
hindi ko magits ang rami
21. 6. It is a tool used to check the squareness of a stock. A. Try square B. Meter stickC. L-square D. Pull-push rule 7. Stated below are procedures in accomplishing the requisition form in order to acquire materials needed in th EXCEPT: A. State the name of the project and date when you requested for materials. B. Fill in the classification of a project and its purpose. C. Write the number of required materials D. Get a replacement for the materials and tools found defective. 8. It refers to the indicated name of tools and equipment. A. Label B. Brand C. Packaging D. Store 9. Which of the following DOES NOT belong to the group. A. C-clamp B. Bench vise C. Bar clamp D. Chisel 10. Tool used for smoothening flat surfaces A. Chisel B. Plane C. Steel square D. Cabinet scraper 11. How are tools and equipment used in carpentry being classified? A. According to its quality B. According to its brandC. According to its useD. According to its functionality 12. Which of the following is an example of portable power tools? A. Jigsaw B. Bar clamp C. Spirit Level D. Auger bit 13. How to lubricate tools and equipment used in carpentry? A. According to the availability of grease gun B. According to preventive maintenance schedule C. According to the availability of personnel D. According to the availability of the said tool and equipment 14. Why is it important to free from sand grits, the housing or case of pull-push rule ? A. To avoid wearing off, of the graduations B. To make it more usableC. To extend its storage life D. To make it safe during project making 15. It refers to a scale of a measuring tool. A. Mensuration B. Graduation C. FractionD. Geometric Shapes
Answer:
6. C
7. B
8. A
9. D
10. B
11. C
12. A
13. A
14. A
15. C
22. 7. A condition of training people to follow cleaning disciplines independently.a. sortingc. sanitizingb. sweepingd self-discipline8. What do you call to the tools that are not able to perform its regular functionbecause of impaired and damage part?a. functional toolsc.powertoolsb. Nonfunctional toolsd. handtools9. What do you call to the tools manipulated by hands without using electricalenergy such as puller, hacksaw, pull-push rule, pliers, hammer, and others?a. powertoolsc. lubricantsb. pneumatic toolsd. handtools10. Which of the following hand tools is used to remove gears and hubs from shafts,bushings from blind holes, and cylinder liners from engine blocks?a. wrenchesc. pullersb. pliersd. srewdrivers
Answer:7. B. sweeping8. B. Nonfunctional tools9. D. handtools10. C. pullersI'm sure that's correctI HOPE IT CAN HELP ^_^✨Carry on learning✨
23. INTRODUCTION PRE-TEST Read the questions carefully. Write the answer on a separate sheet of paper. 1. Which measuring tool is used to measure the internal size of an object? A) Steel Square B) Outside Caliper C) Inside Caliper D) Pull Push Rule (Tape Measure) 2. What is the function of a framing square (steel square)? A) Measure angles B) Measure length C) Measure thickness D) Measure volume 3. How should you handle a try-square? A) Hold it firmly and cautiously B) Use it for other purposes C) Put it in your pocket D) Use it without caution 4. What is the basic conversion factor for inch to centimeters? A) 1 inch = 2.54 centimeters B) 1 inch = 25.4 centimeters C) 1 inch 0.3937 centimeters = 1
1. cInside callipers are used to measure the internal size of an object. The upper caliper in the image (on the right) requires manual adjustment prior to fitting. Fine setting of this caliper type is performed by tapping the caliper legs lightly on a handy surface until they will almost pass over the object.2. Bmeasuring lengths and for calculating angles.3. A4.A2.54 centimetersThe value of 1 inch is approximately equal to 2.54 centimeters. To convert inches to the centimeter values, multiply the given inch value by 2.54 cm.
24. 1. It is used to measure the voltage, resistance and current of a circuit. It connected in parallel or series with the circuit depending on what to measure. A. ammeter B. micrometer C. ohmmeter D. volt-ohm-milliammeter 2. It is used to measure the diameter of wires/conductors in circular mils. It can measure small and big sizes of wires and cables. A. ammeter B. micrometer C. ohmmeter D. voltmeter 3. A measuring tool used to measure the length of an object in centimeter and inches. A. ruler B. test light C. wire gauge D. pull-push rule 4. A pocket sized tool used to test the line wire or circuit if there is current in it. A. ruler B. test light C. wire gauge D. pull-push rule 5. An instrument used to measure the amount of electrical current intensity in a circuit. A. ammeter B. micrometer C. ohmmeter D. voltmeter 6. It is a measuring tool used to measure length, width and thickness of short flat object A. ruler B. test light C. wire gauge D. pull-push rule 7. It is used in determining the size of wires/conductors. A. ruler B. test light C. wire gauge D. pull-push rule 8. It is an instrument used to measure electrical pressure or voltage of a circuit. A. ammeter B. micrometer C. ohmmeter D. voltmeter 9. It is used to measure current flowing in a conductor. It is hanged in a conductor. A. ohmmeter B. voltmeter C. micrometer D. Clamp ammeter 10. It is used to zero-in the pointer before measuring resistance. A. Pointer C. Range Selector knob B. Test probe positiveD. Zero-ohm adjusting-Knob 11. What makes it possible to select different functions and range of the ohmmeter? A. Pointer C. Range Selector knob B. Test probe positive D. Zero-ohm adjusting-Knob Nonsense answer = report
Answer:
1.a
2.d
3.c
4.b
5.c
6.d
7.b
8.a
9.d
10.a
11.b
25. Date: Grade & Section: Directions: Choose the letter of the best answer. Write the letter of the correct answer on the space provided before each other. 1. What classification of tools can be used after a period of time? A condemned B. functional C. Non-functional D. Repaired 2. What classification of tools is considered condemned? A. condemned B. functional D. Repaired C. Non-functional 3. What is the process of checking the list of tools and equipment in the shop? A. Inventory B. Labeling C. Requesting D. Tagging 4. What is done by running a flat file over the ends of saw teeth? A. Filling B. Honing C. Joining D. Setting 5. What kind of tool is used in setting the teeth of a saw? A. File B. Plier C. Saw set D. Wrench 6. Which of the following tools is used in sharpening tooth cutting tools? A. Electric Grinder B. Oilstone C. Sand Paper D. Triangular, Slim Taper File -7. What do you call to the process of putting a tag on a defective tool to avoid using it? A. Labelling B. Signing C. Posting D. Pricing 8. What is a substance introduced between two moving surfaces to reduce friction? A. Alcohol B. Lubricant C. Sealant D. Water 9. What is used to encompass lubricating base oil derived from crude oil? A. Lanolin B. Mineral Oil C. Vegetable Oil D. Water 10. What kind of rule (4ft) 1.20m to (6ft) 1.80m commonly used by carpenters for rough layout? A. Caliper B. Measuring Tape C. Push-pull Rule D. Zigzag Rule 11. Which of the following type of lubricant is applied to hand tools to prevent rust formation? A. Grease B. Mineral Oil C. Solvent D Vegetable Oil 12. What is the process of reshaping the cutting edge of a tool? A. Grinding B. Joining C. Honing D. Whetting 13. What is used to measure long distance available from 3.00m to 7.5 meter long? A. Extension Rule B. Measuring Tape C. Push-pull Rule D. Zigzag Rule 14. What is used for measuring outside diameter of cylindrical objects? A. Caliper B. Measuring Tape C. Push-pull Rule D. Zigzag Rule 15. What is the process of sharpening edge, cutting tools after whetting? A. Grinding B. Joining C. Honing D. Whetting 16. What is used to measure longer distance available from 25 meters to 100 meters long? A. Extension Rule B. Measuring Tape C. Push-pull Rule D. Zigzag Rule 17. What is the actual sharpening of the teeth of a saw? A. Filling B. Honing C. Joining D. Setting 18. Which of the following kind of ule is used for measuring inside distances such as rooms, windows and cabinets? A. Extension Rule B. Measuring Tape C. Push-pull Rule D. Zigzag Rule 19. What is the process of bending the teeth of the saw slightly outward? B. Honing C. Joining D. Setting 20. Why is important to introduce a lubricant between two moving parts? A. To reduce friction C. To improve heat emission B. 'Top stick the bearings D. TO minimize smooth rotation A. Fillingguys patolong Naman
Answer:
B.functionalC.Non-fictionalB.labelingC.JoiningB.plierD-Trangural slimB.signingB.lubricantB.mineral oild.zigzag ruleA.greaseA.grindingD.zigzag ruleA.caliperA.grindingD.zigzag ruleC.joiningC.push-pull ruleD.settingA.fillingCheck mo na lng kong tama ba o mali para ma perfect mo:)
26. Column B Column A 1. A component that resists the flow of current 2. A measuring instrument for measuring angles 3. A device that can temporarily store an electric charge 4. It can be used to draw circles or arcs, parts of circles 5. A device in which a voltage applied to one of the terminals can control current that flows across the other two terminals 6. Used to select different functions and range of the meter 7. It is used to connect the circuit to the electrical components being tested 8. A device used to precisely measure linear dimensions 9. A needle-shaped rod that moves over the scale of a meter 10. It is also called metal tape measure, used for measuring long, short, straight lengths a. Compass b. Transistor c. Pointer d. Resistor e. Test Probes f. Capacitor g. Vernier Caliper h. Protractor i. Inductor j. Push-pull Rule k. Divider 1. Range Selector Knob QUE
Answer:
1G
2e
3a
4b
5c
6i
7f
8h
9
10d
27. 7. A measuring tool used to measure length, width and thickness of short flat object andsketching straight lines.A. Ruler/foot rule B. Pull-push ruleC. Wire gaugeD. Voltmeter8. A measuring tool used to measure the length of an object in centimeter and inches.A. Wire gaugeB. Ruler/foot ruleC. Pull-push rule D. Test light9. Below is an example of unit of measurement, except.A. second B. Meter C. Kilometer D. Ammeter10. It refers to the visual observation of an expert on the appearance of the tools andipment.A. functionalityB. Visual inspectionC. PerformanceD. Power supply
Answer:
7. a. ruler/foot rule
8. b. ruler/foot rule
9. a. second
10. b. visual inspection
(i hope it helps po!^^)
28. 1. It is a device that can used to produce an item or accomplish a task, but that is not consumed inthe process.a. Non-functional tools and equipment b. Machine tools c. Tool d. Pneumatic tools2. What are tools manipulated by hands without using electrical energy such as: puller hacksaw, pull-push rule, pliers, hammer and othersa. Machine/Power tools b. Functional tools and equipment c. Pneumatic tools d. Hand tools3. These are tools or instruments activated by air pressure and designed around three basic devices:the air cylinder, the vane motor and the sprayer.a. Pneumatic toolb. Machine toolsc. Hand toolsd. Power tools
Answer:
1.C
2.D
3.A
Explanation:
Hope it helps:-)
29. 1. The following are procedures in segregating and labeling non-functional tools and equipment except one. A. Conduct an inventory of tools and equipment. B. Record the number of non-functional tools and equipment. C. Segregate tools that are serviceable or unserviceable. D. Do not report the number of tools and equipment that are non-functional but subject for repair. 2. A material manufactured from the thin layer or pieces of wood that are glued together. A. gravel C. G-1 sheet B. plywood D. cement 3. Tools repair and maintenance is important because A. it makes work faster C. it improves work B. it ensures safety D. it reduces time 4. Antonio is trying to measure the long piece of lumber given to him by his uncle. What type of tool does Mark need? A. push-pull rule C. ruler B. meter stick D. protractor 5. Which of the following working conditions below does NOT produce hazards? A. Falling objects C. Radiation B. Safe working environment D. Heat 6. Which of the following practices ensure safety in garments shop? A. Wear personal protective equipment properly. B. Use fingers to feed fabric into the machine. C. Turn the power on when making adjustments to the sewing machine. D. Do not wipe dry spilled oils on the floor. 7. Why is it necessary to wear personal protective equipment (PPE) at all times? A. PPE can increase a worker's exposure to a health hazard in the workplace. B. PPE can minimize workers' exposure to a hazard in the workplace. C. PPE can reduce a worker's exposure but must be used improperly to be effective. D. PPE is a requirement for employment
Answer:
be alm m b n andyan akes s loob ng pader nio
30. What's inRegular maintenance and checking of hand tools and power toolswill help to ensure that they operate with the optimum efficiency at all timesThis will not only help to keep tool operating costs low, but it can also increasetool safety and productivityDirections: List down examples of defects and non-functional tools that youhave observed in workplace or house. Write your answer on a separate sheetof paperObserved Defects/ProblemCarpentry Tool or EquipmentExample: pull push rulestock up tape due to rust or improper used1.2.34.
Answer:
1. Cool Down Heated Tools. ...
2. Clean Regularly. ...
3. Lubricate. ...
4. Sharpen Bits and Blades. ...
